SMV300 O/M.QXD 6/21/01 7:46 AM Page 1
Thank you
For purchasing the Multi CD audio system from Scott. This uniquely designed product has a built-in vertical
3-CD player with a 40 track programmable memory and repeat playback. It also features a clock and great
sounding digital tuning AM/FM stereo radio with 20 memory presets.
We are sure that this unit will provide you with many years of exceptional performance with a minimum of
care and maintenance. Please review the contents of this instruction manual completely and carefully before
operating your unit, to make sure that you understand all functions and operations and get the maximum
benefit out of all the great features included in this product.
The serial number of your unit can be found on a label on the back of the cabinet. We suggest that you
record the serial number in the space provided below in case this information is ever needed at a future
date.
Model Number: SMV300
Serial Number _______________________________________
LASER SAFETY: This unit employs a laser. Only
qualified service personnel should attempt to
service this device due to possible eye injury.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
ADJUSTMENTS
USE
OF
CONTROLS,
PERFORMANCE
CAUTION: TO REDUCE THE RISK OF ELECTRIC
DO NOT REMOVE COVER (OR BACK). NO
OR
SHOCK,
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
PROCEDURE HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DANGEROUS VOLTAGE
The lightning flash with arrowhead symbol,
FCC INFORMATION
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
ATTENTION
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
DANGER:
Invisible and hazardous laser radiation when
open and interlock failed or defeated. Avoid
direct exposure to beam.
RISK OF FIRE - REPLACE FUSE
AS MARKED
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
FCC WARNING:
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This equipment may generate or use radio
frequency energy. Changes or modifications to
this equipment may cause harmful interference
unless the modifications are expressly approved
in the instruction manual. The user could lose
the authority to operate this equipment if an
unauthorized change or modification is made.
1
SMV300 O/M.QXD 6/21/01 7:46 AM Page 3
Remote Control Battery Installation
The remote control transmitter is designed to operate with two (2) “AA” size batteries (not included). To
install the batteries, slide the battery compartment cover open on the back of the remote control (see figure
4) and insert two (2) “AA” size batteries observing the polarity indicated in the compartment. Replace the
battery compartment cover.
–
+
+
–
Figure 4
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed
batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
(Follow battery manufacturer’s directions.)
AUX IN
You can connect an external audio device, such as a cassette deck, TV, VCR, satellite, video game, etc.,
into these jacks. Simply connect the left and right cables of the external device into the Left and Right AUX
IN jacks on the rear of the unit. When using the unit connected to the AUX IN jacks, press the AUX Function
button on the main unit.
LINE OUT
You can connect an external recording device, such as a cassette recorder, into these jacks. Simply connect
the left and right cables of the external recording device into the Left and Right LINE OUT jacks on the rear
of the unit.
DIGITAL OUT
NOTE: Remove the plug from the DIGITAL OUT jack before using.
You can connect an external DIGITAL recording device, such as a minidisc or CD recorder, into this jack.
Simply connect the optical cable (not included) of the external digital recording source into the DIGITAL OUT
jack on the rear of the unit.
HEADPHONE JACK
Connect a pair of stereo headphones (not included) to this jack for private listening without disturbing others.
The speakers are shut off when headphones are connected to the headphone jack.
3
SMV300 O/M.QXD 6/21/01 7:46 AM Page 4
LOCATION OF CONTROLS AND INDICATORS
FRONT
REAR
1
2
3
4
20
5
6
21
22
7
8
9
10
11
12
13
14
15
23
24
25
16 17 18 19
1. CD Buttons (1,2,3)
14. AM/FM Function Button
15. AUX Function Button
16. PLAY/PAUSE (❿ ) Button
17. STOP (I) Button
2. CD DOOR OPEN/CLOSE Button
3. CD Compartment 1
4. CD Doors
5. Palm Sensors
18. TUNING/SKIP/SEARCH ( ) /(
Buttons
)
6. CD Compartment 2
7. CD Compartment 3
8. TIMER Button
9. Display
10. Headphone jack
11. SLEEP Button
19. VOLUME L/M Buttons
20. DIGITAL OUT Jack
21. FM Wire Antenna
22. LINE OUT Jacks
23. AC Cord
12. FM STEREO Button
13. CD/SELECT Function Button
24. AUX IN Jacks
25. Speaker Terminals
4
SMV300 O/M.QXD 6/21/01 7:46 AM Page 5
REMOTE
1
2
3
4
5
6
13
14
15
7
8
9
16
10
11
12
17
18
1. POWER Button
2. Number Buttons (0-9, +10)
3. CD/SELECT Function Button
4. FM/AM Function Button
5. EQ (Equalizer) Button
6. PLAY/PAUSE (❿ ) Button
7. TUNING/SKIP/SEARCH ( )/( ) Buttons
8. STOP (I) Button
9. CD DOOR OPEN/CLOSE Button
10. CD Buttons (1,2,3)
11. INTRO Button
12. RANDOM/MEM L Button
13. VOLUME L/M Buttons
14. AUX Function Button
15. MUTE Button
16. PROG (Program)/MEMORY Button
17. REPEAT/MEM M Button
18. REMAIN/MODE Button
5
SMV300 O/M.QXD 6/21/01 7:46 AM Page 6
SETTING THE CLOCK
When the unit is first plugged in, the time display will blink. Set the time as follows:
1
2
3
While the unit is OFF (POWER Set the correct hour (and AM/PM) When finished setting the hour,
button will be red), press the using the TUNING/SKIP/ press the PROG/MEMORY
PROG/MEMORY button on the SEARCH (
remote and the hours will blink.
) or (
) button.
button on the remote again and
the minutes will blink.
4
5
Set the correct minute using the When finished setting the hour,
TUNING/SKIP/SEARCH (
) button.
) or press the PROG/MEMORY and
the clock will be set.
(
NOTE:
MUTE
If the time display is blinking, then the clock needs to be set.
1
EQ (PRESET EQUALIZER) Buttons:
This unit has 4 preset equalizer settings that automatically
adjust the sound levels for the desired genre. Press the EQ
button for your listening preference (FLAT, ROCK, CLASSIC
and POP); the respective indicator will light in the display.
2
1
To temporarily mute the sound, press the
MUTE button ❶; "MUTE" will appear in the
display and the sound will be muted. Press
the MUTE button ❶ again or one of the
VOLUME buttons ❷ to restore the sound.
6
SMV300 O/M.QXD 6/21/01 7:46 AM Page 7
OPERATING INSTRUCTIONS
LISTENING TO THE RADIO
1
2
3
1
2
Press the POWER button; the Press the AM/FM Function button ❶ Select
a
station using the
TUNING/SKIP/SEARCH ( ) or
) button.
button color will change from red
to green which means the unit is
on.
to select the radio. Press the AM/FM
button again to select AM or FM.
If listening to FM, press the FM If you press and hold the TUNING/
(
STEREO button ❷ to select MONO
or STEREO. Noise present in FM
can be reduced by setting this to
MONO.
SKIP/SEARCH (
) or (
)
button for 2 seconds, the unit will
automatically scan to the next
broadcasting station.
4
5
1
1
2
Adjust the VOLUME ❶ and Preset When you have finished listening,
press the POWER button; the
button color will change from
green to red which means the unit
is in the Standby mode.
Equalizer ❷ buttons as desired.
Hints for Better Reception
FM - Make sure that the FM Antenna Wire is extended to its full length. You may have to vary the direction
of the antenna to find the strongest signal for each FM station.
AM - The AM ferrite bar antenna is located inside the cabinet. It may be necessary to turn the unit slightly so
that the internal antenna is pointing in the direction of the AM transmitter. You may have to experiment to
find the position that provides the strongest reception for each of your favorite AM stations.
7
SMV300 O/M.QXD 6/21/01 7:46 AM Page 8
SETTING RADIO PRESETS
This unit can preset 20 AM and 20 FM radio stations for convenient recall.
1
2
3
Press the POWER button; the Press the AM/FM Function button Press
button color will change from red to select the radio. Press the SEARCH (
the
TUNING/SKIP/
) or ( ) button to
AM/FM button again to select AM
or FM.
to green which means the unit is
on.
find the desired station.
4
5
6
3
1
2
Press the PROG/MEMORY button Within 5 seconds, press the Within 5 seconds, press the
RANDOM/MEM L❶/ REPEAT/ PROG/MEMORY button again to
on the remote.
MEM M button ❷ or the Number set the station in the selected
memory.
buttons ❸ on the remote to select
Repeat steps 4-6 to preset more
stations.
the desired preset number.
RECALLING RADIO PRESETS
1
2
3
2
1
1
1
2
1
2
Follow steps 1 and 2 above. You can also use the Adjust the VOLUME ❶ and Preset
Press the Number buttons ❷ on RANDOM/MEM L❶/ REPEAT/
Equalizer ❷ buttons as desired.
the remote to directly select a MEM M button ❷ on the remote
preset. For example, to select
preset 15, press +10 button ❶ ,
followed by the 5 button ❷.
to cycle through the presets; the
station will automatically be
tuned in.
8
SMV300 O/M.QXD 6/21/01 7:46 AM Page 9
PLAYING COMPACT DISCS (CD-R Compatible)
NORMAL PLAYBACK
1
2
3
Press the POWER button; the Press the CD/SELECT Function Press the CD DOOR OPEN
button color will change from red button.
to green which means the unit is
on.
/CLOSE button to open the CD
compartment doors, or place your
hand in front of CD 2 area (see
page 2).
NOTE: If you have not already
done so, remove the CD transit
lock cards from the CD
compartments now.
4
5
Press one of the CD buttons
(1,2,3) to select the CD in the
respective compartment. The
selected button will turn green.
Playback will automatically start.
Insert a CD into one or all of the compartments by gently pressing a
disc, label side up, onto the spindle until it locks in place. Close the CD
doors and the total number of tracks and playing time on the disc will
appear on the display.
6
7
8
1
2
1
1
2
2
1
Playback will continue until all the To stop playback before the disc If you are finished listening, press
tracks on the disc have been ends, press the STOP (I) button the CD DOOR OPEN/CLOSE
played.
button ❶ to open the CD
Compartment doors. Remove
your disc(s), close the CD
Compartment doors and turn the
power off ❷.
❶. Press the PLAY/PAUSE (❿ )
button ❷ to begin playback again.
Adjust the VOLUME ❶ and Preset
Equalizer ❷ buttons as desired.
9
SMV300 O/M.QXD 6/21/01 7:46 AM Page 10
CD PAUSE CONTROL
1
2
During CD playback, if you wish to
pause the disc momentarily, press
the PLAY/PAUSE (❿ ) button
Press the PLAY/PAUSE (❿ )
button again to release Pause
and resume normal CD playback.
again. Playback stops but the disc The sound returns and the
continues to spin and the elapsed elapsed time stops flashing.
time flashes in the CD Display.
TO BEGIN PLAYBACK FROM A SPECIFIC TRACK
1
2
3
1
2
You can also directly select tracks
by using the Number buttons ❶ on
the remote control. Once selected,
they will automatically play. If
selecting a track over 9, press the
+10 button ❷ repeatedly until the
desired first digit appears. For
example, to select track 22, press
the +10 button ❷ twice, and the
“2” Number button ❶.
After you insert the disc into the CD When the desired track number
player and the total number of appears in the display, press the
tracks/elapsed time appear on the
display, you may press either the
PLAY/PAUSE (❿ ) button.
Playback will begin on the track
you selected.
TUNING/SKIP/ SEARCH (
) button to select a specific
track for playback.
) or
(
FORWARD/REVERSE SKIP TRACK AND HIGH-SPEED MUSIC SEARCH (
/
)
1
2
3
During playback, depress and hold
either the TUNING/SKIP/ SEARCH
(
) or (
) button to move the
player forward or backward within
a track to locate a specific musical
passage. The player will move
forward or backward at high speed
as long as the buttons are
depressed. When you release the
During playback, press the
During playback, press the
TUNING/SKIP/SEARCH
(
)
TUNING/SKIP/ SEARCH (
)
button once to move the player back
to the beginning of the previous
track. Press the TUNING/SKIP/
button once to advance the player to
the beginning of the next track. Press
TUNING/SKIP/ SEARCH (
) button, normal playback will
resume at that point.
) or
(
the TUNING/SKIP/ SEARCH (
)
SEARCH (
) button repeatedly to
button repeatedly to advance the
player to higher number tracks.
move the player back to lower-
numbered tracks.
10
SMV300 O/M.QXD 6/21/01 7:46 AM Page 11
REPEAT PLAYBACK
1
2
3
3
2
2
2
2
1
1
1
To repeat all of the inserted discs To repeat all of the tracks on a To repeat a single track, press the
continuously, press the REPEAT disc continuously, press the REPEAT button ❶ a third time. “1”
button ❶ once. “ALL DISC” will REPEAT button ❶ twice. “1 DISC”
appear in the display. Press the will appear in the display. Press TUNING/SKIP/ SEARCH (
) button ❷ or the Number
will appear in the display. Press the
) or
(
PLAY/PAUSE (❿ ) button ❷ to the PLAY/PAUSE (❿ ) button ❷
buttons ❸ on the remote to select
the specific track that you wish to
repeat. The specific track you
selected will be automatically
played and repeated continuously.
begin all discs repeat.
to begin all tracks repeat.
NOTE:
To cancel Repeat Playback, press the REPEAT button repeatedly until the Repeat indicator disappears from
the display.
PROGRAMMED PLAYBACK
The CD player in this unit has a 40-track programmable memory that allows you to program up to 40 tracks
on any disc for playback in any desired order. You may program 40 different tracks or you may also program
certain tracks to play more than once.
To perform programmed playback, proceed as follows:
1
3
2
2
1
Press the CD/SELECT Function
button.
Press the PROG/MEMORY button
❶; the display will show “00 P-01”
and “MEMORY” will blink.
Open the CD Compartment doors
and insert your disc(s) in the
compartments. Close the CD doors.
Wait for the CD player to read the
table of contents and display the
total number of tracks on the disc.
Select
a
disc using the
CD/SELECT button ❷; the disc
number will appear in the display.
PROGRAMMED PLAYBACK SECTION CONTINUED ON NEXT PAGE.
11
SMV300 O/M.QXD 6/21/01 7:46 AM Page 12
4
5
6
2
2
1
1
1
1
3
3
Press
SEARCH (
the
TUNING/SKIP/ Press
) or (
or the Number buttons ❷ on the or the Number buttons ❷ to select press the PLAY/PAUSE (❿ )
the
TUNING/SKIP/ After programming up to 40 tracks
) or ( ) button ❶ in the CD Program Memory,
) button ❶ SEARCH (
button to begin programmed
playback; “MEMORY” will appear
in the display and playback will
begin on the first track that you
programmed.
remote to select the first track that the next track you wish to
you wish to program. Press the program. Press the PROG/
PROG/MEMORY button ❸ to set MEMORY button ❸ to set the
the memory.
memory.
Repeat this step to program up to
40 tracks.
The player will continue to play all of the tracks that you programmed
in the order in which you programmed them. When the last
programmed track has been played, the player will stop but the
program is still active. If you press the PLAY/PAUSE (❿ ) button ❶
again, playback will start on the first track you programmed and will
continue until all the programmed tracks have been played.To cancel
the Programmed Playback mode, press the STOP (I) button ❷ while
in the Stop mode.
7
1
2
CHANGING THE PROGRAM
1
2
3
2
2
2
2
1
3
3
3
3
1
1
While in the Stop mode, press the To delete a programmed track, To add a programmed track,
PROG/MEMORY button press the TUNING/SKIP/ press the PROG/MEMORY
SEARCH ( ) or ( ) button ❷ button ❶ repeatedly until “00”
❶
repeatedly until the desired
program number is displayed, then to change the track number to “00”. blinks in the display, then press
press the CD/SELECT ❷ button to Confirm by pressing the the CD/SELECT ❷ button to add a
PROG/MEMORY button ❶.
change the disc, and/or the
TUNING/SKIP/ SEARCH ( ) or
) button ❸ to change the track.
disc, and/or the TUNING/SKIP/
SEARCH ( ) or ( ) button ❸
to add a track. Confirm by pressing
(
the PROG/MEMORY button ❶.
12
SMV300 O/M.QXD 6/21/01 7:46 AM Page 13
PROGRAMMED REPEAT
1
2
3
It is also possible to use the
Program and Repeat functions
together to repeat a specific
program indefinitely. First,
program the tracks you wish to
hear in the order you wish to hear
them, as described above. Then,
press the REPEAT button once.
Program Repeat operation will
continue indefinitely until you
press the STOP (I) button, open
the CD door or turn the power off.
Press the PLAY/PAUSE (❿ )
button to begin programmed
repeat playback. The player will
play the tracks you selected in the
order in which you programmed
them. When the last track in the
program has been played, the
entire program will begin again.
INTRO PLAYBACK
Intro playback will play the first 10 seconds of each track.
1
2
3
With a CD is inserted, press the When you hear a song you would To stop Intro playback, press the
INTRO button; “INTRO” will like to continue listening to, press STOP (I) button.
appear in the display. The unit will the INTRO button again.
automatically play the first 10
seconds of each track.
TO RANDOMLY PLAY BACK A CD
1
2
With a CD is inserted, press the With a CD is inserted, press the
RANDOM button once; RANDOM button twice;
“RANDOM” and “ALL DISC” will “RANDOM” and “1 DISC” will
appear in the display. The unit appear in the display. The unit
will play all the tracks on all the will play all the tracks on the
CDs in random order.
selected CD in random order.
13
SMV300 O/M.QXD 6/21/01 7:46 AM Page 14
REMAIN/MODE BUTTON
1
2
When a disc is playing, press the REMAIN/MODE
button repeatedly to cycle as follows:
When in the Stop or a mode other then CD, press
the REMAIN/MODE button repeatedly to cycle as
follows:
1
2
3
Remaining time of current track.
Remaining time of current CD
Normal display, elapsed time of current track.
1
Time Display (in Aux mode, time is
displayed)
Additional presses will show you the time and the
timer, explained on page 15.
Additional presses will show you the time and the
timer, explained on page 15.
INSTANT PLAYBACK
If listening to the radio or auxiliary input, simply press one of the CD buttons (1,2,3) and the unit will
automatically play the respective CD.
SLEEP TIMER
This feature will allow you to set the unit to automatically turn itself off after up 90 minutes in 10 minute
steps.
1
2
3
2
1
Press the POWER button; the Select a radio station ❶ or a CD Press the SLEEP button on the
button color will change from red
to green which means the unit is
on.
main unit; “SLEEP” will appear in
the display. The unit will continue
to operate for 10 to 90 minutes
(depending on the selection), and
then turn off.
❷ as desired.
TO CANCEL SLEEP TIMER
To cancel, simply press the SLEEP button again until “SLEEP’ disappears from the display.
14
SMV300 O/M.QXD 6/21/01 7:46 AM Page 15
ON/OFF TIMER
This feature will allow you to set the unit to turn on and off automatically at preset times.
1
2
3
2
1
Press the POWER button; the Select a radio station or a CD that Press the REMAIN/MODE button
button color will change from red you would like to be playing when ❶ repeatedly until, “TIMER ON”
to green which means the unit is the unit switches on.
appears in the display, then
immediately press the PROG/
MEMORY button ❷ and the hours
will blink.
on.
If selecting CD, you can also
program tracks into memory to be
played.
4
5
6
1
1
1
1
2
2
2
1
Set the correct hour (and AM/PM) Set the correct minute using the Press the REMAIN/MODE button
using
SEARCH (
the
TUNING/SKIP/ TUNING/SKIP/SEARCH (
) or ( ) button ❶. ) button ❶.
) or ❶ again until, “TIMER OFF”
(
appears in the display, then
When finished setting the hour, When finished setting the hour, immediately press the PROG/
press the PROG/MEMORY press the PROG/MEMORY MEMORY button ❷ and the hours
button ❷ on the remote again and button ❷ and the clock will be set.
will blink.
the minutes will blink.
7
8
9
1
1
2
Set the hour and minute the same To activate the timer to turn on Press the POWER button to turn
way as you did for the Timer On.
and off at the preset times, press the unit off and into the Standby
the TIMER button on the main mode; the POWER button will
unit; “TIMER” will appear in the light red. When the actual time
display.
reaches the Timer On time, the
unit will turn on.
NOTES:
•
While setting, carry out each step within 5 seconds, otherwise the operation will time out and you will
have to start again.
•
To cancel the timer, press the TIMER button until “TIMER” disappears from the display.
15
SMV300 O/M.QXD 6/21/01 7:46 AM Page 16
CARE AND MAINTENANCE
.Caring for Compact Discs
• Treat the disc carefully. Handle the disc only by its edges.
Never allow your fingers to come in contact with the shiny,
unprinted side of the disc.
• Do not attach adhesive tape, stickers, etc. to the disc label.
• Clean the disc periodically with a soft, lint-free, dry cloth.
Never use detergents or abrasive cleaners to clean the
disc. If necessary, use a CD cleaning kit.
• If a disc skips or gets stuck on a section of the disc, it is probably dirty or damaged (scratched).
• When cleaning the disc, wipe in straight lines from the center of the disc to the outer edge of the disc.
Never wipe in circular motions.
Z
COMPACT
• This unit is designed to play only compact discs bearing the identification logo as shown here.
Other discs may not conform to the CD standard and may not play properly.
DIGITAL AUDIO
• Compact Discs should be stored in their cases after each use to avoid damage.
• Do not expose compact discs to direct sunlight, high humidity, high temperatures, or dust, etc. Prolonged
exposure or extreme temperatures can warp the disc.
• Do not stick or write anything on either side of the disc. Sharp writing instruments, or the ink may damage
the surface.
Cleaning the unit
• To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other furniture. Use caution
when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
16
SMV300 O/M.QXD 6/21/01 7:46 AM Page 17
TROUBLESHOOTING GUIDE
Should this unit exhibit a problem, check the following before seeking service.
Symptom
Radio
Possible Cause
Solution
Noise or sound distorted
on radio broadcasts.
Station not tuned properly for
AM or FM.
Retune the AM or FM broadcast
station.
FM: The FM Antenna wire is not
extended.
Extend FM Antenna wire.
AM: Unit is not positioned correctly.
Rotate unit for best reception as this
unit has an internal AM antenna.
FM STEREO indicator
does not light.
Poor FM signal being received or
switch is not set to FM STEREO.
Retune station, try another station or
set FM STEREO switch to FM STEREO.
Station is not broadcasting in stereo.
Change stations.
AM or FM, no sound.
The AM/FM Function button is not
pressed.
Press the AM/FM Function button.
Volume at minimum.
Increase Volume.
Compact Disc Player
CD Player will not play.
The CD Function button is not
pressed.
Press the CD Function button.
Insert CD with label side up.
CD is not installed or installed
upside-down.
CD skips while playing.
CD Doors will not open.
Disc is dirty or scratched.
Wipe disc with cloth or use
another disc.
Power must be on, and the CD
Turn the power on, press the CD
Function button must be pressed first. button, and then open the CD Door.
AUX
No Sound.
The AUX button is not pressed.
External unit not on.
Press the AUX Function button.
Turn external unit on.
Cable not connect to AUX IN jacks.
Connect cable securely.
General
No Sound.
Headphones connected.
Remove the Headphones.
Connect speaker cables.
Speaker cable not connected.
17
SMV300 O/M.QXD 6/21/01 7:46 AM Page 18
TO FIND THE LOCATION AND
PHONE NUMBER OF YOUR
NEAREST AUTHORIZED
SERVICE CENTER...
CALL TOLL FREE: 1-888-837-8370
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-888-837-8370
FOR CUSTOMER SERVICE, PLEASE WRITE TO:
H.H. Scott Inc.
Consumer Affairs Dept.
1901 Diplomat Drive
Farmers Branch, TX 75234
18
SMV300 O/M.QXD 6/21/01 7:46 AM Page 19
H.H. SCOTT, INC.
LIMITED WARRANTY
What does this warranty cover?
Any manufacturing defects in original material, including original parts and workmanship, under normal use and
conditions.
For how long?
For a period of one (1) year from the date of original purchase in the U.S.
What will we do?
If you need service under this Warranty, and you provide us with the dated proof of purchase, we will provide repair
service at no charge for labor and parts at an authorized Depot Repair Facility, or replace the product in our
discretion.
How do you make your warranty claim?
If it becomes necessary to repair your unit, you can obtain the name and mailing location of a Depot Repair Facility by
dialing 1-888-837-8370. You should pack your unit in a well-padded heavy corrugated box, enclose your check or
money order payable to the Depot Repair Facility in the amount of $15.00 to cover the return shipping and handling
costs, and enclose a copy of your proof of purchase (warranty service will not be provided without a dated proof of
purchase). Finally, you should ship the unit prepaid via UPS or parcel post (insured).
What does your warranty not cover?
Your warranty does not cover the following :
• Damage from negligence, misuse, abuse, accident, or failure to follow operating instructions.
• Use of product in a commercial application or rentals.
• Changes or repairs by anyone other than an authorized Depot Repair Facility.
• Damage because your unit is improperly connected to the equipment of other manufacturers.
• Unit on which the serial number has been defaced, modified or removed.
• Damage to equipment not properly connected to the product.
• Cost incurred in shipping your unit to and from an authorized Depot Repair Facility.
• Ordinary adjustments which you can perform as outlined in the owner’s manual.
• Signal reception problems caused by external antenna or cable systems.
• Products purchased, used, serviced, or damaged outside of the United States.
What other limitations apply to your warranty ?
THIS WARRANTY IS NON-TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER AND DOES
NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT. THIS WARRANTY IS VALID ONLY IN THE
UNITED STATES OF AMERICA. ANY APPLICABLE IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED IN DURATION TO A PERIOD OF THE EXPRESSED WARRANTY AS
PROVIDED ABOVE BEGINNING WITH THE DATE OF ORIGINAL PURCHASE AT RETAIL AND NO WARRANTIES,
WHETHER EXPRESSED OR IMPLIED, SHALL APPLY TO THE PRODUCT THEREAFTER. WE MAKE NO
WARRANTY AS TO THE FITNESS OF THE PRODUCT FOR ANY PARTICULAR PURPOSE OR USE.
THE EXTENT OF OUR LIABILITY UNDER THIS LIMITED WARRANTY IS THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND IN NO EVENT WILL OUR LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE
PURCHASER OF THE PRODUCT. UNDER NO CIRCUMSTANCES WILL WE BE LIABLE FOR ANY LOSS,
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN
CONNECTION WITH THE USE OF THIS PRODUCT.
How does state law apply to your warranty ?
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, BUT YOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES OR
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE, SO THESE RESTRICTIONS
MAY NOT APPLY TO YOU.
HH111N
19
SMV300 O/M.QXD 6/21/01 7:46 AM Page 20
VERTICAL 3 CD PLAYER WITH
DIGITAL TUNING AM/FM
STEREO RADIO
OWNER’S MANUAL
SMV300
SMV300 O/M.QXD 6/21/01 7:46 AM Page 21
PART NO.: 100-5098
106-01
Printed in China
|